500 Lindahl Parkway, Ashland City,TN 37015
The
Expert’s
Choice
™
Commercial Gas Water Heater
The Sandblaster
®
Force
™
delivers the money-saving performance of State
Industries original Sandblaster commercial water heater, plus a solution to
negative air pressure, a problem found in many commercial applications.
For example, in restaurant kitchens, commercial range hoods and exhaust fans
draw large amounts of air out of the room. This creates negative air pressure in
the room, which can deprive an ordinary commercial gas water heater of
sufficient make-up air required for safe, efficient, proper operation.
In negative air pressure situations, downdrafts can occur inside an ordinary
water heater, compressing the burner flame, resulting in impaired water heating
performance and recovery efficiency. Negative air pressure can also generate
Carbon Monoxide buildup, and other potential safety hazards.
Sandblaster
®
Force
™
is the solution, because it doesn’t share the inside air! It is
equipped with a factory-installed blower and two-pipe system for intake of
make-up air and separate exhaust venting. This unique air delivery system
(patent pending) insures that Sandblaster
®
Force
™
is immune to negative air
pressure. Sandblaster
®
Force
™
also helps reduce space heating or air
conditioning costs, because it does not consume heated or cooled air from
inside the building.
Long Vent Runs Mean Installation Flexibility
The Force
™
installs just about anywhere, thanks to intake and exhaust vent runs
of up to 135 feet horizontally or vertically on models SDV80-140, SDV100-199
and SDV100-260. The SDV75-70 vent run is 50 feet horizontally or vertically.
The SDV100-400 has a maximum vent run of 110 feet using 6 inch pipe. (Note:
The first 10 feet of exhaust run for the SDV100-400 must be CPVC Schedule 40
pipe minimum.) See the vent run chart or the owners manual for specific
venting information.
NEW!
Exhaust pipe
power-vents
products of
combustion to
outside building.
Air intake pipe
draws all
combustion
make-up air
from outside
building.
■
3-Year or 5-Year Tank Warranty.
■
ASME Construction available on SDV100 260 and SDV100-400.
■
Turbo-Force Ring Self-Cleaning Feature – Patented design
automatically reduces harmful sediment buildup inside the tank.
Sandblaster
®
Force
™
stays energy-efficient, so it saves money throughout
its life. Turbo-Force dip tube in model SDV75 70.
■
Labor Replacement Allowance (LRA) for installing contractor if
heater needs replacement during basic 3-year warranty: $250 LRA on
75-70 model; $500 LRA on 80-140 and 100-199 models; $1000 LRA on
100-260 and 100-400 models.
■
Non-Condensing Design helps prevent corrosion. No condensate pump
or drain needed.
■
Installs with 3˝, 4˝ or 6˝ ** Schedule 40 PVC pipe, depending on the
model and vent run.
■
Two 45°
3˝ or 4˝ (depending on model)
Schedule 40 Elbows, with
screen, supplied for use as vent caps. Schedule 80 Elbows on 100-400.
■
Integral Automatic Blower – With 110/120 Volt electrical system. Maximum
electrical draw: 2 Amps on SDV75 70, 12 AMPS on all other models.
* Check owners manual and local codes for specific venting requirements. Each 90° elbow reduces
maximum run by 5 feet.
**Exhaust vent run on SDV100-400 must be CPVC Schedule 40 minimum for the first 10 feet of the run.
■
Intermittent electronic ignition.
■
Reinforced tank design for longer life – The Sandblaster
®
Force
™
glasslined tank is reinforced with extra steel in all the most critical areas, to
insure long tank life.
■
Removable lanced-port steel burner, with multiple tubular construction,
for even heat distribution, maximum efficiency, quiet operation. SDV75 70 has
a formed aluminized steel burner.
■
Foam insulation – Reduces heat loss over 2
1
⁄
2 times more effectively than
standard fiberglass.
■
Factory-installed Temperature & Pressure safety valve (T&P Valve).
■
Factory-installed Energy Cut-Off (“ECO”) safety switch.
■
Multiple Magnesium Anode Rods – for extra protection against electrolytic
tank corrosion. SDV75 70 has a single large diameter magnesium anode.
■
Tank Inspection Port for easy access to tank interior on all models
except SDV75 70.
■
Maximum Hydrostatic Working Pressure: 150 psi. (ASME 160 psi.)
SDV100-400
Non-Condensing
Up To 85%
Thermal
Efficiency
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels